Instrumentation info

P&F Barrier -

KCD2-SR-Ex2.SP - Switch Amplifier

Used for:

• This is an isolated barrier is used for intrinsic safety applications.
• The device transfers digital signals from NAMUR sensors or dry contacts from the hazardous area to the non-hazardous area.
• useful for detecting positions, end stops, and switching states.
• The device output changes the state when the input signal changes the state.

Decoding:

KCD2-SR-Ex2.SP
------------------
K: K-System
------------------
C: Version with removable terminal blocks, 12.5 mm width
------------------
D: DC power supply
------------------
2: 24 V
------------------
SR: Switch amplifier with relay output
------------------
-
Ex: Isolated Barriers, not applicable to Signal Conditioners
------------------
2: Number of channels
------------------
.
SP:Special function, if available
 

Notes:

• 2-channel
• Dry contact or NAMUR inputs (Signal type Digital Input)
• Relay contact outputs
• Supply  Connection either from Power Rail or terminals 9+, 10-
• Line fault detection (LFD)
• Via DIP switches the mode of operation of can be reversed  and the line fault detection can be switched off.
• Supply: Connection Power Rail (or) terminals 9+, 10-
• Supply Rated voltage Ur 19-30 V DC
• Rated current Ir ≤ 30 mA
• Input
  Connection terminals 1+, 2-; 3+, 4-
  Open circuit voltage/short-circuit current approx. 10 V DC / approx. 8 mA
  Switching point/switching hysteresis 1.2 - 2.1 mA / approx. 0.2 mA
  Line fault detection breakage I ≤ 0.1 mA , short-circuit I ≥ 6.5 mA
• Output
  Connection terminals 5, 6; 7, 8
  Output I signal ; relay
  Output II signal ; relay
  Minimum switch current 2 mA / 24 V DC
• Ambient temperature -20 - 60 °C

P&F Barrier -

KFD2-EB2-R4A.B - Redundant Power Feed Module

Used for:

• Interface for Power Rail
• The power feed module supplies the Power Rail with a voltage of 24 V DC and a maximum current of 4 A
• The device is designed for applications requiring redundant power.
• In the event of a device fault or a wiring, fault of any isolator on the Power Rail, the collective error messaging relay alerts the controller via a binary I/O point.
  This relay can be configured as normally-open or normally-closed.

Decoding:

KFD2-EB2-R4A.B
------------------
K: K-System
------------------
F: Version with removable terminal blocks, 20 mm or 40 mm width
------------------
D: DC power supply
------------------
2: 24 V
------------------
EB: Power feed module
------------------
 

Notes:

• Supply: Connection terminals 11+, 12-, terminals 8+, 9-
  Rated voltage Ur 20-30 V DC
• Output: Connection Power Rail
  Output rated operating current max. 4 A
• Fusing 5 AT/250 V AC, Replaceable fuse
• A green LED on the front of the device indicates the power state, and a red LED lights up during a fault condition.
• Relay contact output, reversible
• Ambient temperature: -40 - 60 °C
• Note: Redundant systems require 2 KFD2-EB.R4A.B power feed modules.

P&F Barrier -

KFD2-PT2-Ex1-5 - Potentiometer Converter

Used for:

• This is an isolated barrier is used for intrinsic safety applications.
• It provides the source voltage to a potentiometer and transfers its wiper position from hazardous areas to safe areas.
  It then converts the signal to a 4 mA - 20mA current output.
• The unit can be used in a 3-, 4-, or 5-wire configuration depending on the required measurement accuracy. 
• The barrier’s potentiometer can be used to compensate for lead resistance up to 5 % of the hazardous area potentiometer value.
• Lead resistance compensation adjustment

Decoding:

KFD2-PT2-Ex1-5
------------------
K: K-System
------------------
F: Version with removable terminal blocks, 20 mm or 40 mm width
------------------
D: DC power supply
------------------
2: 24 V
------------------
PT: Potentiometer converter
------------------
-
Ex: Isolated Barriers, not applicable to Signal Conditioners
------------------
1: Number of channels
 

Notes:

• 1-channel
• Signal type Analog input
• Supply  Connection either from Power Rail (or) terminals 11+, 12-
• Rated voltage Ur 20-35 V DC
• Input
  Potentiometer input
  Connection terminals 4-, 5-, 3+, 2+, 1+
  Types of measuring 3-, 4-, 5-wire technology
  Nominal resistance 800 Ω to 100 kΩ
  Supply voltage approx. 4.7 V
  Lead resistance 5 % of the potentiometer resistance (adjustable)
• Output
  Current output 4 mA-20 mA
  Connection terminals 7-, 8+
• Indicators/settings
  Control elements potentiometer
  Configuration via potentiometer
• Ambient temperature: -20 - 60 °C

in 3-wire configurations

Jumpers must be used on terminals 1, 2 and 4, 5 .

in 4-wire connections.

A jumper must be used between terminals 4 and 5

In the 5-wire mode of operation

the potentiometer voltage is measured at terminals 2 and 5 and automatically readjusted.

Front side potentiometer

can be used to compensate for lead resistances up to 5 % of the potentiometer value

During adjustment, the potentiometer is set to 100 % of its value and the output signal is adjusted to 100 % of the required value. This adjustment can be repeated setting the potentiometer to 0 %.

Accessories (some of them are)

• K-250R Measuring resistor 
• K-500R0%1 Measuring resistor
  
  This resistor can be used to convert 0-20 mA to 0-5 V. 
  Precision resistor.